How to use ROMON to recover from a bad boot image on a Cisco ASA

Note that this can be applied to other Cisco devices, but commands will vary from device to device. The specific commands here apply to the Cisco ASA 5500 series.
Connect a computer to the console port of the device using a Cisco console cable. Use a terminal emulator such as Putty set for 9600 baud, 8 data bits, no parity, 1 stop bit, no flow control.
Power cycle the device.
During startup, press the Escape key when you see the prompt to enter ROMMON mode.
It is always a good idea to retain the previous boot image on the device during an upgrade, if space permits. If there is an alternative image available on the flash memory you can issue the boot command as follows:
rommon #1> boot asa821-k8.bin
Launching BootLoader...
Boot configuration file contains 1 entry.

Loading disk0:/asa821-k8.bin... Booting...
Platform ASA5505
Loading...

If you don't have a local copy of an alternative boot image and need to copy an image from a network location, define the interface settings as follows:

rommon #1> ADDRESS=172.31.255.1rommon #2> SERVER=10.200.4.29rommon #3> GATEWAY=172.31.255.4rommon #4> IMAGE=asa821-k8.binrommon #5> PORT=GigabitEthernet0/1GigabitEthernet0/1 Link is UP
MAC Address: 0021.a09a.bf89
Test connectivity using the ping server command.
rommon #6> ping serverSending 20, 100-byte ICMP Echoes to server 10.200.4.29, timeout is 4 seconds:

Success rate is 100 percent (20/20)
Load the software image using the tftp command. This assumes that you have a TFTP server running on the target address and a copy of the required image in the target directory.
rommon #7> tftpROMMON Variable Settings:
ADDRESS=172.31.255.1
SERVER=10.200.4.29
GATEWAY=172.31.255.4
PORT=GigabitEthernet0/1
VLAN=untagged
IMAGE=asa821-k8.bin
CONFIG=
LINKTIMEOUT=20
PKTTIMEOUT=4
RETRY=20

tftp asa821-k8.bin@10.200.4.29 via 172.31.255.4
Received 16275456 bytes
Launching TFTP Image...
After the image is loaded the device automatically exits ROMMON.

Cannot start Microsoft Outlook. Cannot open the Outlook window.

I had an interesting problem over the weekend... on my HOME computer!! O_o

Trying to launch Outlook, I was receiving the error message “Cannot start Microsoft Outlook. Cannot open the Outlook window.”

It appears that the configuration file for the Navigation Pane can get corrupted and this will prevent Outlook from launching successfully.

This can be remedied by running OUTLOOK.EXE with the /RESETNAVPANE switch.

How to Edit an INI file using VBScript

Modify the highlighted sections with the appropriate changes.

Note that you can use environment variables to ensure that it will work on all systems. eg. If you use %SystemRoot% it will work whether windows is installed in C:\WINNT or D:\Windows.


' This script can be used to edit entries in ini files
'
' Written by Sean Bradley
' Version 1.0
' Last modified 11/09/09
'
Const ForReading = 1
Const ForWriting = 2
Set oShell = CreateObject( "WScript.Shell" )

'Set the target file and backup directory.
'Note that I've used an environment variable here to ensure it works on all systems.
'
targfile=oShell.ExpandEnvironmentStrings("%SystemRoot%") + "\editthisfile.ini"
backdir=oShell.ExpandEnvironmentStrings("%TEMP%") + "\"
Set objFSO = CreateObject("Scripting.FileSystemObject")

'Make sure the file exists to prevent errors.
'
if objFSO.FileExists(targfile) then
'Copy it to the backup directory then open the file.
objFSO.CopyFile targfile, backdir, true
Set objTextFile = objFSO.OpenTextFile(targfile, ForReading)

'Read through each line of the file for the entry you want to set
'
Do Until objTextFile.AtEndOfStream
strNextLine = objTextFile.Readline
intLineFinder = InStr(strNextLine, "IniFileEntrytoEdit")
If intLineFinder <> 0 Then

'Set your new entry here.
'
strNextLine = "IniFileEntrytoEdit=My Entry in the File"
End If
strNewFile = strNewFile & strNextLine & vbCrLf
Loop

objTextFile.Close

'Write the file with the new entry
'
Set objTextFile = objFSO.OpenTextFile(targfile, ForWriting)

objTextFile.WriteLine strNewFile
objTextFile.Close
End If

Log File Cleanup

I needed a tool to clean up log files that exceed a certain age and I remembered a simple executable that I used to have called deleteifolderthan.exe that did just what was required, but when I went looking for it, I couldn't locate it anywhere.

Giving up on that, I decided to write my own script. I needed something that would delete log files over a month old in subdirectories of a parent directory. This is what I came up with:

Const ParentFolder = "E:\Logs"
Const MaxDays = 31
Set objFSO = CreateObject("Scripting.FileSystemObject")
Set objFolder = objFSO.GetFolder(ParentFolder)
Set colSubFolders = objFolder.SubFolders
For Each objDir in colSubFolders
Set colFiles = objDir.Files
For Each objFile in colFiles
If DateDiff("d",objFile.DateCreated,now) >= MaxDays Then
objFSO.DeleteFile(objFile.Path)
End If
Next
Next

If you wanted to delete old logs in a single folder, you could simplify this to:

Const WatchFolder = "E:\Logs"
Const MaxDays = 31
Set objFSO = CreateObject("Scripting.FileSystemObject")
Set objDir = objFSO.GetFolder(WatchFolder)
Set colFiles = objDir.Files
For Each objFile in colFiles
If DateDiff("d",objFile.DateCreated,now) >= MaxDays Then
objFSO.DeleteFile(objFile.Path)
End If
Next

Cheers,
Sean

JDE IE Recommended Settings

I just got back from the snow! Had an awesome time snowboarding in Thredbo.

I thought I'd quickly post this Group Policy ADM Template that I developed to configure Internet Explorer with some settings recommended by Oracle and JDE for running their OneWorld Web Client.

; This policy template has been written to optimise the IE web client
; with Internet Explorer due to a limitation in this browser and the
; number of connections to the web server as per recommendations from
; Oracle for IE to interact with JDE
;
; The IE changes are used to change the number of connections to the
; server which can help to improve the performance of the web client
; and rendering of the menus.
;
; The CSV MIME Type is used to fix an issue when opening CSV files in
; the web client (please see Oracle documentation for further details).
;
; This is a System Policy template and does not use the preferred
; Group Policy method
;
; Refer to Microsoft TechNet article Q323639 for further information.
; Therefore these registry settings are permanent.
;
; When viewed via a Group Policy Object Editor, you must enable the view for system
; policies, which will appear as red icons as oppose to the standard blue ones.
;
; Windows 2000 Active Directory Group Policies:
; Click on Administrative Templates
; Righ click
; View >
; Select Show Policies Only so that it removes the tick.
;
; Windows 2003 Active Directory Group Policies:
; Click on Administrative Templates
; Righ click
; View >
; Select Filtering...
; Deselect Only show policy settings that can be fully managed
; so that it removes the tick.
; Select OK
;
;
;Developed by: Sean Bradley
;Contact info: Contact via http://draxonic.blogspot.com/
;Date last modified: 07/07/2009
;version: 1.0
;This file is provided AS IS for informational purposes to help assist other
;administrators in maintaining a high degree of client manageability.
;Be sure to fully test this in a lab environment PRIOR to implementation.
;The author makes no guarantee or warranty. IE: Use at your own risk.

CLASS MACHINE
CATEGORY "JDE Web Client Policies"
POLICY "CSV MIME Type"
KEYNAME "Software\Classes\MIME\Database\Content Type\application/csv"
EXPLAIN "Setting this policy fixes an issue when opening CSV files in the JDE web client."
PART "Set CSV MIME Type" CHECKBOX DEFCHECKED
VALUENAME "Extension"
VALUEON ".csv"
VALUEOFF ""
END PART
END POLICY
END CATEGORY

CLASS USER
CATEGORY "JDE Web Client Policies"
POLICY "Increase Max Connections per Server"
KEYNAME "Software\Microsoft\Windows\CurrentVersion\Internet Settings"
EXPLAIN "Setting this policy changes the number of connections to the server which can help to improve the performance of the web client and rendering of the menus in the JDE Web Client. Note that existing Internet Explorer Maintenance Policy Objects can be used to permit HTTP 1.1 over proxy conenctions."
PART "Increase Max Connections values" CHECKBOX DEFCHECKED
VALUENAME "MaxConnectionsPerServer"
VALUEON NUMERIC 10
VALUEOFF NUMERIC 3
ACTIONLISTON
KEYNAME "Software\Microsoft\Windows\CurrentVersion\Internet Settings"
VALUENAME "MaxConnectionsPer1_0Server" VALUE NUMERIC 10
END ACTIONLISTON
ACTIONLISTOFF
KEYNAME "Software\Microsoft\Windows\CurrentVersion\Internet Settings"
VALUENAME "MaxConnectionsPer1_0Server" VALUE NUMERIC 3
END ACTIONLISTOFF
END PART
END POLICY
END CATEGORY

RSA Server IP Address Change

A gotcha discovered while changing the IP address of an RSA Authentication server.

To change the address of the server, you need to use the rsautil command from the command line:

rsautil update-instance-node --old-host Current_IP_Address --new-host New_IP_Address --instance primary

where:
• Current_IP_Address is the current IP address of the instance, for example,192.168.1.1.
• New_IP_Address is the new IP address of the instance, for example,192.168.200.245.

That's all well and good and is in the administrative guide. Of course, you'll need to reconfigure any devices that are pointing to the IP address of the server as well, such as an authentication agent on your Aventail or ASA.

However, you may see failed authentications and start noticing this in your logs:
Node secret mismatch. Cleared on agent but not on server.

In order to fix this, you'll have to get CLI access to your Aventail or ASA and delete the node secret files from the device. On an Aventail, these will be ststatus.12, securid ( delete them from /var/ace then restart the policy server using /etc/init.d/policyserver restart ). On the ASA it will be 192-168-111-123.sdi. Then connect to your RSA Security Console and manage the existing Authentication agents. You should then be able to select "Manage Node Secret" from the drop-down menu and clear the node secret. The secret will then be renegotiated on first use.

Cheers,
Sean

VMWare View Client Silent Installation

I've been having some trouble figuring out how to prevent VMWare View Client from rebooting a machine upon completion of a silent installation. The standard /norestart switch that you normally pass to msiexec simply results in an error.

In the end, I found two answers. One answer was to perform an administrative installation of the product. Then, you are able to call an installation using the msi file directly and use the normal msiexec command line parameters.

msiexec /qn /norestart /i "VMware View Client.msi" ADDLOCAL=Core DESKTOP_SHORTCUT=0 QUICKLAUNCH_SHORTCUT=0

The second, simpler answer was to pass the property REBOOT=ReallySuppress:

VMware-viewclient.exe /s /v"/qn DESKTOP_SHORTCUT=0 QUICKLAUNCH_SHORTCUT=0 REBOOT=ReallySuppress"

Cheers,
Sean